Aftemarket ATA PTX5 Remote
Includes:
1x Aftemarket ATA PTX5 Remote
1x Battery
Coding Instructions
Compatibility:
DCB-05 (Dual Gate Controller)
GDO-6v3 (EasyRoller)
GDO-6v4 (EasyRoller)
GDO-7v2 (SecuraLift)
GDO-7v3 (SecuraLift)
GDO-8v3 (Shed Master)
GDO-9 (Dynamo)
GDO-9 (Enduro)
GDO-9 (Ero)
GDO-9v2 (SecuraLift)
GDO-9v2 (Enduro)
GDO-9v3 (Dominator)
GDO-9v3 (Dynamo)
GDO-10v1 (Toro)
GDO-11v1 (Securalift Ero)
NES-24v1 (NeoSlider)
RD-40V1
SGO-1 (Elite)
PLEASE NOTE - If you are not 100% sure this remote is compatible with your motor, please send us a picture of your motor/remote and we will be able to advise you.
Includes:
1x Aftemarket ATA PTX5 Remote
1x Battery
Coding Instructions
Compatibility:
DCB-05 (Dual Gate Controller)
GDO-6v3 (EasyRoller)
GDO-6v4 (EasyRoller)
GDO-7v2 (SecuraLift)
GDO-7v3 (SecuraLift)
GDO-8v3 (Shed Master)
GDO-9 (Dynamo)
GDO-9 (Enduro)
GDO-9 (Ero)
GDO-9v2 (SecuraLift)
GDO-9v2 (Enduro)
GDO-9v3 (Dominator)
GDO-9v3 (Dynamo)
GDO-10v1 (Toro)
GDO-11v1 (Securalift Ero)
NES-24v1 (NeoSlider)
RD-40V1
SGO-1 (Elite)
PLEASE NOTE - If you are not 100% sure this remote is compatible with your motor, please send us a picture of your motor/remote and we will be able to advise you.
Includes:
1x Aftemarket ATA PTX5 Remote
1x Battery
Coding Instructions
Compatibility:
DCB-05 (Dual Gate Controller)
GDO-6v3 (EasyRoller)
GDO-6v4 (EasyRoller)
GDO-7v2 (SecuraLift)
GDO-7v3 (SecuraLift)
GDO-8v3 (Shed Master)
GDO-9 (Dynamo)
GDO-9 (Enduro)
GDO-9 (Ero)
GDO-9v2 (SecuraLift)
GDO-9v2 (Enduro)
GDO-9v3 (Dominator)
GDO-9v3 (Dynamo)
GDO-10v1 (Toro)
GDO-11v1 (Securalift Ero)
NES-24v1 (NeoSlider)
RD-40V1
SGO-1 (Elite)
PLEASE NOTE - If you are not 100% sure this remote is compatible with your motor, please send us a picture of your motor/remote and we will be able to advise you.
Coding Instructions
Coding your Remote to your Opener
1. Take any coded remote. Press the button for the function you require until the door / gate is activated and release.
2. Then using a small needle or paper clip press on the Coding Bump in the middle of the remote firmly for two seconds – LED lights.
3. Within 10 seconds pick up the new remote you wish to code.
4. Press the remote button you would like to use to open / close the device for two seconds.
5. Pause for two seconds then press the same button again for two seconds - button should now be coded.
6. Wait for 10 seconds, then press the just coded remoter button to confirm that it operates the device.
Deleting the Codes from Your Motor
1. Turn the power off to the opener.
2. Press and hold Door Code or SW1 button.
3. Turn the power on again, while holding the button. The coding LED will illuminate to indicate that the receiver’s. memory has been deleted.
4. Release the button. All the stored codes including the courtesy light codes should now be all deleted.
Confirm this by pressing the transmitters previously used to operate the device, there should be no response.